{"id":6608,"date":"2026-11-06T05:36:22","date_gmt":"2026-11-06T05:36:22","guid":{"rendered":"https:\/\/plugplaykit.com\/?post_type=docs&#038;p=6608"},"modified":"2026-11-06T12:06:59","modified_gmt":"2026-11-06T12:06:59","password":"","slug":"ppk-q030-digital-pressure-guide","status":"publish","type":"docs","link":"https:\/\/plugplaykit.com\/es\/docs\/ppk-q030-digital-pressure-guide\/","title":{"rendered":"PPK-Q030 Digital Pressure Sensor: I\u00b2C and UART Guide"},"content":{"rendered":"<h2>PPK-Q030 Digital Pressure Sensor: I\u00b2C and UART Guide<\/h2>\n<p>The PPK-Q030 is a digital air pressure sensor module with a 0\u20131500 kPa absolute-pressure range. This guide explains how to choose an interface and interpret readings in a microcontroller project. I\u00b2C and UART are separate purchase options; choose the version that matches your controller and software.<\/p>\n<figure><img decoding=\"async\" src=\"https:\/\/plugplaykit.com\/wp-content\/uploads\/2026\/11\/01-module-1.webp\" alt=\"PPK-Q030 air pressure sensor module with its pressure port and connector\" \/><figcaption>Identify the pressure port, sensor module and electrical connector before planning the mechanical and electrical integration.<\/figcaption><\/figure>\n<h2>1. Choose the right output version<\/h2>\n<table>\n<tbody>\n<tr>\n<th>Configuration<\/th>\n<th>Controller interface<\/th>\n<th>Communication method<\/th>\n<th>Choose it when<\/th>\n<\/tr>\n<tr>\n<td>PPK-Q030 \u2014 I\u00b2C<\/td>\n<td>SCL and SDA bus signals<\/td>\n<td>Register-based commands and reads; clock up to 400 kHz<\/td>\n<td>Your controller software uses an I\u00b2C bus.<\/td>\n<\/tr>\n<tr>\n<td>PPK-Q030 \u2014 UART<\/td>\n<td>UART transmit and receive signals<\/td>\n<td>9600 baud, 8 data bits, no parity, 1 stop bit<\/td>\n<td>Your controller software uses a serial port.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>These interface names describe communication signals, not the positions or colors of the module cable wires. They do not mean that both interfaces are available on every purchased module.<\/p>\n<h2>2. Understand absolute pressure<\/h2>\n<p>Absolute pressure is referenced to a vacuum. Gauge pressure is relative to the surrounding atmosphere. A sensor exposed to ambient air therefore does not normally read zero absolute pressure.<\/p>\n<p>For a project that needs gauge pressure, subtract a suitable ambient absolute-pressure reference from the measured absolute pressure. Do not subtract a fixed atmospheric value unless that approximation is appropriate for the project: ambient pressure changes with location and conditions.<\/p>\n<h2>3. Check size and supply requirements<\/h2>\n<figure><img decoding=\"async\" src=\"https:\/\/plugplaykit.com\/wp-content\/uploads\/2026\/11\/03-dimensions.webp\" alt=\"PPK-Q030 module footprint marked 24 mm by 15 mm\" \/><figcaption>The module footprint is 24 \u00d7 15 mm. The pressure port projects beyond the board; allow clearance for the port, tubing and cable.<\/figcaption><\/figure>\n<table>\n<tbody>\n<tr>\n<th>Parameter<\/th>\n<th>Value<\/th>\n<\/tr>\n<tr>\n<td>Measured medium<\/td>\n<td>Air<\/td>\n<\/tr>\n<tr>\n<td>Pressure range<\/td>\n<td>0\u20131500 kPa absolute<\/td>\n<\/tr>\n<tr>\n<td>Operating supply<\/td>\n<td>2.4\u20135.5 V<\/td>\n<\/tr>\n<tr>\n<td>Module footprint<\/td>\n<td>24 \u00d7 15 mm<\/td>\n<\/tr>\n<tr>\n<td>Conversion current<\/td>\n<td>1.5 mA typical<\/td>\n<\/tr>\n<tr>\n<td>Standby current<\/td>\n<td>2 \u00b5A typical; 3.5 \u00b5A maximum<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<div class=\"note\"><strong>Before applying power:<\/strong> verify the actual module connector assignments and controller electrical compatibility. The supply range is not a guarantee that every interface signal can be driven at any voltage within that range. Chip pin numbers must not be used as cable connector pin numbers.<\/div>\n<p>Use 1500 kPa as the measurement-range limit. Do not treat an absolute-maximum or overpressure rating as an extended measurement range. This guide does not establish a whole-module waterproof rating or suitability for liquid contact.<\/p>\n<h2>4. Use the temperature-first measurement sequence<\/h2>\n<p>The documented I\u00b2C and UART procedures require temperature acquisition before pressure conversion. The internal compensation uses the current temperature.<\/p>\n<figure><img decoding=\"async\" src=\"https:\/\/plugplaykit.com\/wp-content\/uploads\/2026\/11\/ppk-q030-measurement-flow.png\" alt=\"Measurement sequence: acquire temperature, request pressure conversion, wait for completion and decode pressure\" \/><figcaption>Follow the same temperature-first principle with either interface.<\/figcaption><\/figure>\n<ol>\n<li>Acquire the current temperature using the selected interface.<\/li>\n<li>Request the pressure conversion.<\/li>\n<li>Wait for the documented completion indication or response.<\/li>\n<li>Read and decode the returned pressure value.<\/li>\n<\/ol>\n<h2>5. I\u00b2C command and read sequence<\/h2>\n<p>The documented address bytes are <code>0xDA<\/code> for writing and <code>0xDB<\/code> for reading. For controller libraries that expect a seven-bit device address, use <code>0x6D<\/code>; the library supplies the read\/write bit. Check the convention of your library before passing an address.<\/p>\n<table>\n<tbody>\n<tr>\n<th>Operation<\/th>\n<th>Register<\/th>\n<th>Command or data<\/th>\n<\/tr>\n<tr>\n<td>Request temperature conversion<\/td>\n<td>0x0A<\/td>\n<td>Write 0x04<\/td>\n<\/tr>\n<tr>\n<td>Request pressure conversion<\/td>\n<td>0x0A<\/td>\n<td>Write 0x06<\/td>\n<\/tr>\n<tr>\n<td>Check conversion completion<\/td>\n<td>0x13<\/td>\n<td>Bit 0 indicates completion when set<\/td>\n<\/tr>\n<tr>\n<td>Read temperature<\/td>\n<td>0x0F\u20130x10<\/td>\n<td>High byte followed by low byte<\/td>\n<\/tr>\n<tr>\n<td>Read pressure<\/td>\n<td>0x0B\u20130x0E<\/td>\n<td>Most significant byte first<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Poll for completion rather than guessing a fixed conversion delay. In controller software, include a timeout so an absent or disconnected sensor cannot leave the program waiting indefinitely.<\/p>\n<pre>Temperature example:\n0x0F = 0x01, 0x10 = 0x02\nRaw value = 0x0102 = 258\nTemperature = 258 \/ 10 = 25.8 \u00b0C\n\nPressure example:\n0x0B = 0x00, 0x0C = 0x01, 0x0D = 0x86, 0x0E = 0xA0\nRaw value = 0x000186A0 = 100000\nPressure = 100000 \/ 1000 = 100 kPa absolute<\/pre>\n<p>These are documented decoding examples, not readings guaranteed for a particular environment.<\/p>\n<h2>6. UART communication<\/h2>\n<p>Configure the host serial port for <strong>9600 baud, 8-N-1<\/strong>. The command frame begins with <code>0x55<\/code>; a response begins with <code>0xAA<\/code>. The documented frame also contains length, command or data-type fields, payload and a checksum. Validate the complete frame before using its payload.<\/p>\n<table>\n<tbody>\n<tr>\n<th>Command<\/th>\n<th>Purpose<\/th>\n<\/tr>\n<tr>\n<td>0x0E<\/td>\n<td>Acquire current temperature<\/td>\n<\/tr>\n<tr>\n<td>0x27<\/td>\n<td>Acquire high-accuracy temperature<\/td>\n<\/tr>\n<tr>\n<td>0x0D<\/td>\n<td>Acquire current pressure<\/td>\n<\/tr>\n<tr>\n<td>0x26<\/td>\n<td>Acquire high-accuracy pressure<\/td>\n<\/tr>\n<tr>\n<td>0x3C<\/td>\n<td>Acquire predicted pressure<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The source provides these current-temperature and current-pressure request examples:<\/p>\n<pre>Current temperature request: 55 04 0E 6A\nCurrent pressure request:    55 04 0D 88<\/pre>\n<p>Request temperature first. The documented response data types include signed 16-bit temperature and unsigned 32-bit pressure. The examples scale temperature by 10 and pressure by 1000 to obtain \u00b0C and kPa respectively. Do not assume the I\u00b2C byte order applies to the UART payload: the UART example transmits the least significant byte first.<\/p>\n<p>For example, the UART pressure payload <code>A0 86 01 00<\/code> represents <code>0x000186A0<\/code>, or 100000, yielding 100 kPa. A temperature payload <code>02 01<\/code> represents 258, yielding 25.8 \u00b0C. Use signed decoding for negative temperatures.<\/p>\n<h2>7. Check the first readings<\/h2>\n<ul>\n<li>Confirm that software is configured for the purchased interface.<\/li>\n<li>Confirm the supply and connector assignments before troubleshooting software.<\/li>\n<li>For an I\u00b2C address failure, check whether the library expects 0x6D or explicit address bytes.<\/li>\n<li>For UART, check 9600 baud and 8-N-1, then validate framing and checksum.<\/li>\n<li>For a factor-of-1000 pressure error, check the documented raw-value scaling.<\/li>\n<li>For an apparent offset in open air, check whether the application expects absolute or gauge pressure.<\/li>\n<li>Repeat temperature acquisition before pressure conversion.<\/li>\n<\/ul>\n<p>A 24-bit ADC describes the conversion architecture. It must not be interpreted as a guaranteed 24-bit measurement accuracy. Resolution, accuracy and operating conditions are separate specifications.<\/p>\n<h2>Related product<\/h2>\n<p><a href=\"https:\/\/plugplaykit.com\/es\/?post_type=product&amp;p=6604\">PPK-Q030 Digital Air Pressure Sensor \u2014 I\u00b2C and UART options<\/a><\/p>","protected":false},"excerpt":{"rendered":"<p>PPK-Q030 Digital Pressure Sensor: I\u00b2C and UART Guide The PPK-Q030 is a digital air pressure sensor module with a 0\u20131500 kPa absolute-pressure range. This guide explains how to choose an interface and interpret readings in a microcontroller project. I\u00b2C and UART are separate purchase options; choose the version that matches your controller and software. Identify [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"closed","template":"","meta":{"om_disable_all_campaigns":false,"_uag_custom_page_level_css":"","_monsterinsights_skip_tracking":false,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"doc_category":[41],"doc_tag":[],"class_list":["post-6608","docs","type-docs","status-publish","hentry","doc_category-technical-support"],"year_month":"2026-11","word_count":870,"total_views":"6","reactions":{"happy":"0","normal":"0","sad":"0"},"author_info":{"name":"PlugPlayKit Team","author_nicename":"die7uj39gmail-com","author_url":"https:\/\/plugplaykit.com\/es\/author\/die7uj39gmail-com\/"},"doc_category_info":[{"term_name":"Technical Support","term_url":"https:\/\/plugplaykit.com\/es\/docs-category\/technical-support\/"}],"doc_tag_info":[],"uagb_featured_image_src":{"full":false,"thumbnail":false,"medium":false,"medium_large":false,"large":false,"1536x1536":false,"2048x2048":false,"trp-custom-language-flag":false,"mailpoet_newsletter_max":false,"woocommerce_thumbnail":false,"woocommerce_single":false,"woocommerce_gallery_thumbnail":false,"variation_swatches_image_size":false,"variation_swatches_tooltip_size":false},"uagb_author_info":{"display_name":"PlugPlayKit Team","author_link":"https:\/\/plugplaykit.com\/es\/author\/die7uj39gmail-com\/"},"uagb_comment_info":0,"uagb_excerpt":"PPK-Q030 Digital Pressure Sensor: I\u00b2C and UART Guide The PPK-Q030 is a digital air pressure sensor module with a 0\u20131500 kPa absolute-pressure range. This guide explains how to choose an interface and interpret readings in a microcontroller project. I\u00b2C and UART are separate purchase options; choose the version that matches your controller and software. Identify&hellip;","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/docs\/6608","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/docs"}],"about":[{"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/types\/docs"}],"author":[{"embeddable":true,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/comments?post=6608"}],"version-history":[{"count":1,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/docs\/6608\/revisions"}],"predecessor-version":[{"id":6611,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/docs\/6608\/revisions\/6611"}],"wp:attachment":[{"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/media?parent=6608"}],"wp:term":[{"taxonomy":"doc_category","embeddable":true,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/doc_category?post=6608"},{"taxonomy":"doc_tag","embeddable":true,"href":"https:\/\/plugplaykit.com\/es\/wp-json\/wp\/v2\/doc_tag?post=6608"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}