Compact Air Pressure Sensor Module

$5.90

A compact MEMS air pressure sensor module with a 15 mm circular PCB. Choose a 3.3 V or 5 V fixed-output version, or a supply-proportional output, then select the pressure range your controller needs.

Calculate shipping price

Please fill in the fields below with the shipping destination details in order to calculate the shipping cost.

Guaranteed Safe Checkout

The PPK-QY20 is a small MEMS pressure sensor module for air-pressure measurement in controller-based designs. Its circular PCB measures 15 mm across, with a pressure port on the sensor side and a cable connection on the reverse.

Choose the electrical version and pressure range separately. A and B provide specified voltage-output ranges; H provides an output proportional to its supply voltage. Each combination is a separate purchase configuration, not a software-selectable mode.

Key Features

  • 15 mm circular PCB for compact integration.
  • MEMS sensing technology for air-pressure measurement.
  • Three analog voltage configurations: A, B and H.
  • Seven selectable electrical-version and pressure-range combinations.
  • Positive-only and negative-to-positive range options, depending on version.

Technical Specifications

Model PPK-QY20
Sensing technology MEMS
Measured medium Air / gas; verify the intended gas compatibility before installation
PCB diameter 15 mm
Supply voltage A 3.3 V; B 5 V; H 3.3–5 V
Voltage output A 0.5–2.5 V; B 0.5–4.5 V; H 10–90% of supply voltage
Operating temperature for voltage-output type −40 to 84°C
Comprehensive accuracy for voltage-output type 0.5–1%, including zero and temperature drift
Available combinations Seven; see model selection guide

Model Selection Guide

  • | Version | Supply | Output | Available ranges | How to choose |
  • | A | 3.3 V | 0.5–2.5 V | −100 to +100 kPa; 0 to 100 kPa | Match an analog input that accepts the full 0.5–2.5 V signal. |
  • | B | 5 V | 0.5–4.5 V | −10 to +10 kPa; −100 to +100 kPa; −100 to +1000 kPa | Match an analog input that accepts the full 0.5–4.5 V signal. |
  • | H | 3.3–5 V | 10–90% of supply voltage | −10 to +10 kPa; −100 to +100 kPa | Choose for a controller designed to measure an output proportional to the sensor supply. |
  • For H, the stated output range corresponds to 0.33–2.97 V at a 3.3 V supply, or 0.5–4.5 V at 5 V. These values are the stated supply percentages expressed in volts, not a separate calibration or accuracy specification.
  • For a measurement that crosses zero, select a range with a negative lower limit. The A version’s 0 to 100 kPa option does not cover negative pressure. A −10 to +10 kPa version and a −100 to +100 kPa version have different spans even when their electrical output format is the same.

Applications

  • Air-pressure monitoring integrated with a controller that accepts the selected analog output and supply requirements.
  • Positive and negative pressure measurement designs, using the appropriate selected range.

Wiring / Installation

  • The three-wire connection illustration identifies red as supply positive, black as supply negative, and yellow as signal output. Match the actual received module and selected supply voltage before connecting power.
  • The cable illustration specifies a 19 cm lead and an XH connector labeled with a 2.54 mm pitch. Verify the mating connector dimensions before designing a fixed connector footprint.

Compatibility & Important Notes

  • Do not apply the voltage of another version to the selected module. A 5 V supply is not the specified supply for A.
  • The receiver must accept the entire selected output range. A controller’s supply voltage alone does not establish its analog input limits.
  • The voltage-output accuracy figure includes zero and temperature drift; do not treat it as a guarantee of the same percentage of every reading. No independent calibration results are included.
  • Use the selected measurement range as a limit for selection; do not treat an overload figure as an allowed continuous operating range.
  • The exposed PCB needs an appropriate installation environment. Keep liquids away from the electronics and do not assume the module is waterproof or approved for direct liquid contact.
  • Use this module for compatible gas-pressure measurement. This product page does not establish medical-device approval, food-contact certification, or compatibility with flammable or corrosive gases.
Electrical Version

A — 3.3 V / 0.5–2.5 V, B — 5 V / 0.5–4.5 V, H — 3.3–5 V / 10–90% of supply

Pressure Range

−100 to +100 kPa, 0 to 100 kPa, −10 to +10 kPa, −100 to +1000 kPa

Reviews

There are no reviews yet

Add a review
Compact Air Pressure Sensor Module Compact Air Pressure Sensor Module
Rating*
0/5
* Rating is required
Your review
* Review is required
Name
* Name is required
Add photos or video to your review
Shopping Cart
PPK-QY20 Compact Air Pressure Sensor Module — PPK-QY20 air pressure module front with pressure port and three-wire cable on a white background.Compact Air Pressure Sensor Module